![]() ![]() ![]() A well-made key log template will ensure that you will have an effective document for monitoring and tracking the various keys that are going in and out of a particular department.You may also see maintenance logģ. A key log template or any type of log template, such as a daily log template, is a useful document that can be used as reference for when you are outlining or formatting your document.You may also see decision logĢ. I'll continue to try and find an example of this other error I can reproduce and submit that when I find it.Download What Are the Uses of Key Log Templates?ġ. I have not been able to duplicate that one to submit yet, but I wonder if when this happens might have something to do when this other error happens. Additionally, the cells below that one do not get shifted up properly and I have to go back in an manually shift things around to get it straightened out. For some reason the joined cells properties get shifted to the one besides it after a delete. There is another bug/problem I run into a lot of times when I delete/insert rows and have joined cells. It is like the complexity has to reach a certain level before it starts to fail. When I tried to make a simple two-file Master/Read example of the problem in the past, it would actually work as expected as you have proven. This is something I have noticed as well and one of the reasons it took me some time to find/create an example where the problem showed itself. I tried it with build 3 and it's no different but if I create two new files each with a spreadsheet with one as a driver and the other as driven in order to replicate a simple example, it works as expected with the cell in the driven file going to #PENDING before doing a Recompute. I'll upload the files in the next post as I've run out of upload files on this post. Now that I have a smaller set that I can provide it is easier for me to give examples. If you have any other questions, please let me know. I'm hoping that those of you that understand that back side of this can figure out what is going wrong and come up with a fix for me. when I did, it was usually because I had an error somewhere in a spreadsheet that was holding up the recalculating. I did not have this problem often with version 19. ![]() When It does update later, I find that I have to go back and fix things.Īnyway, I have noticed that version 20 is MUCH less reliable when it comes to updating links. However, I have ran into a few situations where that didn't happen and I've gone on to keep building and not have the latest information. MOST of the time as each page is loaded, it then correctly updates the values. However, most of my assemblies are much more complicated with a lot more parts tied together and the only way I can get them to update any links if I change the Master is to save the file, close it, and then open everything back up. This is a relatively simple assembly here with only a few moving parts where it is not too hard to find the right cells to update. Now if I want to change the value to another one, I have to repeat this whole process, change the Master value, recompute the three cells in he SSS_LevelMountMount spreadsheet, and then recompute and it will move again. So to duplicate the problem I am having, first, open all the files and navigate to the Telescope_Assembly file to show the top view of the mount. The assembly is held by Telescope_Assembly. 01_Pedestal_Base, 02_Level_Mount_Bottom, 03_Level_Mount_Top, and 04_Horizontal_Adjustment_Plate. In my example, I'm building a telescope mount. It is advisable to load the Master file first when loading my assembly, although it normally works if you don't too. It is a bit of work to do it this way, but I rarely have problems. This allows me to keep my parts parametric and reduce the chances I run into the TNP. The Master acts as a control location for changes I want to make to move various parts as well as stores common measurements that I might need on two separate parts. I have a Master Spreadsheet that I use to set and send values to other spreadsheets for the various parts I'm working with on my assembly. I don't think this is the same issue as reported in the above post, but it might be related. I was finally able to put together some files that cause me the problem with the spreadsheet values I have not updating properly. I decided that this is a different issue and decided to give it, its own topic.Ĭhanging value in Spreadshet does not update linked Constraints ![]() I originally put this in the following post as I was following that thread as I had similar problems with Spreadsheet WB. ![]()
0 Comments
Leave a Reply. |